Call us now for a free quote

718-939-9700Architect's Corner
Select Page

Perforated Doors


WORK EXCLUDED – Preparation of openings, structural supports unless specified (refer to option below), removable soffits or access panels, trim, field painting. On motor operated doors, exclude wire, wiring, or disconnect switches.


OPERATION – to be (Push-up, with handles) (chain and reduction gears; maximum pull of 35 lbs.) (Chain Hoist with reduction gears and removable arm) (Motor – refer to options below).


CURTAIN – The curtain is constructed from 22 gauge G-60/G-90 galvanized steel or a baked-on polyester coat in grey, beige, or white. Other colors, gauges and material (stainless steel/aluminum) are available – please consult factory .The curtain features .062 diameter openings on .094 staggered centers allowing air and light to pass through without sacrificing security.


COUNTERBALANCE ASSEMBLY – to consist of tempered helical torsion springs with a 25% safety factor, mounted on shaped cast anchors, supported by a continuous solid torsion rod. This mechanism to be permanently lubricated and enclosed within a steel pipe shaft. Deflection of shaft not to exceed .03″ per ln. ft. The spring tension adjusting wheel is to be readily accessible from outside the bracket plate.


SPRING COUNTERBALANCE – Option for band type springs for smaller doors shall consist of flat blue steel wrapped around a 2″ or 3″ pipe shaft and mounted into a galvanized steel spring box.


BRACKETS – to be not less than 1/4″ thick steel plate, to contain sealed self-aligning ball bearings for suspension of the counterbalance assembly. Gears to be high grade iron, cast from machine-cut patterns. 
GUIDES -to be of extruded aluminum with retainers for end links. To be fitted with wool pile inserts to eliminate metal-to-metal contact.


HOODS – to be of (aluminum) (galvanized steel) (stainless steel), minimum #24 Gauge, stiffened top and bottom. Omit if coil to be above ceiling.


LOCKING PROVISION FOR PADLOCKS – to be (slide bolts on push-up grilles) (chain holder on chain grilles) (slide bolts on grilles) (self-locking gearing on motor grills). 
FINISH -on (aluminum) (stainless steel) to be mill finish. Steel surfaces to be one shop coat of metal primer except on galvanized surfaces.


STRUCTURAL STEEL TUBE SUPPORTS – In standard type weight with floor seats to be furnished by grille mfr., sized as required, pre-drilled for guides and brackets.

MOTOR OPERATORS – to be integral assemblies with Nema rated electrical components, Model (MO) (H), consisting of high torque motor, braking system, self-locking gearing, (Model MO gear reducer with worm gears in oil bath) (Model H chain sprocket gearing) emergency chain operator with disconnect and electrical safely interlock, internal reversing magnetic controller, pushbutton station with open-close-stop, internal pre-wiring. Motor to be removable without affecting chain operation or limit switch setting.

SPECIAL ELECTRICAL CONTROLS – to include (flush-mounted key switches) (additional push-button stations) (weatherproof switches).

SAFETY EDGE BOTTOM BARS – to be furnished on motor operated, which, upon contact with an object, is to stop (or reverse) the downward travel.

REMOVABLE SOFFITS – (for coils above hung ceilings) to be supplied, if indicated to be by grille manufacturer, in (galvanized steel) (aluminum) (stainless steel).

MORTISE CYLINDER LOCK – to be provided, engaging at both ends (concealed within bottom bar) (curtain type waist-high or as otherwise indicated) (operable one side) (operable both sides).

FINISH – on aluminum (curtain) (bottom bar) (guides) to be (clear anodized) (Duranodic bronze). On stainless steel (curtain) (bottom bar) to be #4 satin finish. (Hood, where required, to match).

EMERGENCY-OPEN RELEASE – to be provided for flush mounting. Activating handle will cause grille to open for emergency egress.

Product Line

Rolling Steel Solid Door

Commercial Coiling Grills

UL Classified Fire Rated Products

Doors for Special Applications

Spare Parts For Doors